Exterior paint for 180 ft of smooth fibre cement at 9 ft high, 2 coats
| Paint | 7.95gal |
|---|---|
| What to buybuckets pay from about 3.6 gal up | 2 × 5 gal |
| Wall area180 ft perimeter × 9 ft, less 6 windows and 2 doors | 1,488ft² |
| Spread ratethe easiest exterior surface to cover — closest to interior drywall | 350ft²/gal |
| First coat | 4.25gal |
| Each later coat15% further on a sealed surface | 3.7gal |
| Doubling the first coat would say0.55 gal more than needed | 8.5gal |
- Perimeter
- 180 ft
- Wall height
- 9 ft
- Siding
- smooth fibre cement
- Coats
- 2
- Windows
- 6
Texture decides the spread rate, not the brand
smooth fibre cement takes about 350 ft² per gallon. The same house in smooth fiber cement would take noticeably less, and in brick noticeably more — the mortar joints drink more than the brick does.
180 ft of perimeter at 9 ft high, less 6 windows and two doors, is 1,488 ft². At 2 coats that is 7.95 gallons.
The second coat is cheaper
Once the surface is sealed, paint spreads about 15% further. Doubling the first coat would say 8.5 gal — 0.55 gal more than you need, sitting in the garage until it separates.
Two weather limits matter more than the gallon count
Surface temperature has to stay above about 10 °C for the whole cure, not just while you are painting. A warm afternoon followed by a cold night gives a film that never properly coalesces, and it comes off in sheets the following spring.
Dew point matters as much as rain. Early-morning painting on a clear autumn day fails constantly for exactly this reason — the siding is wet with dew that you cannot see.
Wash first, and wait
Paint over chalky or dirty siding fails at the interface however good the paint is. Pressure-washed wood needs two or three dry days; a moisture meter reading under 15% is the honest test, not "it looks dry".
Back-roll anything you spray
Spray lays paint on the surface. Back-rolling works it into the grain and the grooves. On smooth fibre cement that is the difference between six years and twelve.
Notes
- **Surface texture, not brand, decides the spread rate.** Smooth fibre cement takes about 350 ft² per gallon — the easiest exterior surface to cover — closest to interior drywall. The same house in smooth fibre cement would take 4.25 gal per coat against 4.25 here.
- **Two weather limits matter more than the gallon count.** Surface temperature must stay above about 10 °C for the whole cure, not just while you are painting — a warm afternoon followed by a cold night gives a film that never coalesces. And the surface has to be dry: dew point matters as much as rain, which is why early-morning painting on a clear autumn day so often fails.
- On smooth fibre cement in sound condition, spot-prime bare and repaired areas rather than priming the whole wall. A full prime coat here buys very little.
- Wash it first, and let it dry properly. Paint over chalky or dirty siding fails at the interface no matter how good the paint is, and pressure-washed wood needs two or three dry days before it is ready — a moisture meter reading under 15% is the honest test.
- Back-roll anything sprayed. Spray alone lays the paint on the surface; back-rolling works it into the grain and the grooves, and on smooth fibre cement that is the difference between six years and twelve.
- Buy it all at once and box it. Exterior walls are seen in full sun from a distance, which is the least forgiving lighting there is for a batch difference.
Nearby sizes
- Exterior paint for 170 ft of smooth fibre cement at 9 ft high, 2 coats
- Exterior paint for 190 ft of smooth fibre cement at 9 ft high, 2 coats
- Exterior paint for 160 ft of smooth fibre cement at 9 ft high, 2 coats
- Exterior paint for 200 ft of smooth fibre cement at 9 ft high, 2 coats
- Exterior paint for 180 ft of smooth fibre cement at 10 ft high, 2 coats
- Exterior paint for 180 ft of smooth fibre cement at 18 ft high, 2 coats
- Exterior paint for 180 ft of lap siding at 9 ft high, 2 coats
- Exterior paint for 180 ft of shiplap siding at 9 ft high, 2 coats
- Exterior paint for 180 ft of smooth fibre cement at 9 ft high, 1 coats
- Exterior paint for 180 ft of smooth fibre cement at 9 ft high, 3 coats
- Exterior paint for 180 ft of smooth fibre cement at 9 ft high, 2 coats
- Exterior paint for 180 ft of smooth fibre cement at 9 ft high, 2 coats
Read more
- How Much Exterior Paint — Texture Decides It, Not BrandThe gap between smooth fibre cement and bare brick is nearly three to one. The gap between the cheapest and dearest paint is nothing like that.
- Paint Coverage per Gallon by Surface — the Full Table, and Why the Label Is OptimisticEvery label says 400 square feet. Almost no real surface delivers it, and the ones that miss badly miss by half.
- Cost to Paint a Room — Where the Money Goes, and Why Trim Costs More Than WallsPaint is about a tenth of the bill. Prep and trim are most of it, and trim does not scale with room size at all.
- How Much Paint for a Room — Spread Rate Belongs to the Surface, Not the TinChoosing paint by the coverage claim on the label compares products on a number that describes a wall you do not have.